Bluewild's new trawler will primarily be used for shrimp and whitefish trawling. Ulstein has developed a battery hybrid propulsion solution that is expected to provide large reductions in diesel consumption and emissions. This is solved by improving the efficiency of a wide range of power requirements.
The fishing company Bluewild will replace the trawler ‘Langenes’ from 1986 with a newbuilding to fish their quotas on cod pollock and haddock. In addition, Bluewild also has a license to fish for shrimp to achieve high utilisation of the vessel all year round. These fisheries require different levels of towing power.
Designed for the lowest possible emissions
The new trawler will have an efficient hybrid system with two propellers that can combine battery power with both diesel-electric and diesel-mechanical propulsion. This will make the fishing vessel very fuel-efficient compared to a trawler with traditional propulsion.
"Through analyses and tank tests, we estimate that this hybrid system, together with other energy-saving measures on board, will give at least a 25 percent reduction in fuel consumption and emissions compared to a similar modern trawler performing this type of combination fishing, and the savings can in some operations exceed 40 per cent," says Frode Sollid, system architect in Ulstein Design & Solutions AS.
Sustainable fisheries that challenge conventional solutions
“We have teamed up with the fishing company Bluewild over a longer period to challenge the conventional solutions within the trawler industry”, Sollid continues.
“Shrimp fishing requires a large towing force, while the power demand is not as great for whitefish trawling and when transiting to and from the fishing grounds the power requirement is even lower. The hybrid propulsion system is adapted to both fisheries. If designing and planning only for maximum engine power to ensure that the vessel will be able to perform all the assignments in the operation profile, the vessel will be expensive to operate and lead to unnecessary emissions during the less energy-intensive operations. In such development work, it is therefore important to ask the question: Can this be done in another way?”
The first step towards lower energy consumption
The first step in the process towards lower energy consumption was to map how the vessels use their power system and look at the most important properties for the system. For a freezer trawler, the dominant mode of operation is trawling, while the vessel is rarely transiting at high speeds. Together with the shipowner, the choice was made to focus on increasing the efficiency during trawling. It was therefore chosen to install two propellers instead of the traditional solution with one propeller because the increased propeller area increases the vessel’s towing efficiency. The propellers are placed in separate skegs in a twin-skeg hull, which provides great advantages in terms of placement of the propulsion equipment and increases the propeller efficiency.
More possibilities for energy saving with double propeller
“Once you go for two propellers, you get new opportunities to operate the vessel in ways you do not have on vessels with only one. By calculation, two propellers use less energy together than one propeller to achieve the same towing power. Also, one of the propellers can be loaded more than the other to steer the vessel. Generally, fishing vessels get a large added resistance when compensating for wind, waves and currents with large rudder angles. By being able to deliver part of the steering power with the propellers, the power requirement will be further reduced. Additionally, the ship is equipped with rudder nozzles instead of the usual rudder behind the propeller. During the model test at Sintef in Trondheim, it was demonstrated that the rudder nozzles were significantly more efficient than ordinary rudders. With this solution, the trawler will be very efficient when trawling also in challenging weather and during manoeuvring”, says Erwin Jager, sales manager fisheries at Ulstein Design & Solutions.
A solution that can reduce emissions in the fishing fleet
Ulstein's team has taken into use their experience from the development of the propulsion systems on the anchor handling vessels Olympic Hera and Olympic Zeus, which were nominated for the Green Ship Technology Award, and linked this to the analyses of the operational requirements of the trawler.
“Both for an anchor handler and a trawler, great demands are placed on towing power. We have looked at how reference vessels in the fishing fleet are used, and for most of the time, they are used for trawling, while only a relatively small part of the time is related to sailing, and then usually at relatively low speed. In consultation with the shipowner, a conscious choice was made to prioritise the properties during trawling and optimise the hull for minimum resistance at moderate speed”, says Sollid.
“Energy savings have been considered throughout the project and these solutions combined will contribute to a significant potential for reductions in fuel consumption and emissions in the fishing fleet.”
Holistic design development
Ship designer Bjørnar Hatløy, who has led the development of the ULSTEIN FX101 design, follows up:
“We have considered this holistically and have especially worked with performance, safety and functionality,” he says, and elaborates:
“We have looked at how the very different operations can be carried out as economically and energy-efficient as possible and based on this we have designed a system architecture that is optimal for performing efficiently at a low, medium and high power consumption. The system architecture must be able to handle the entire span of operations with low environmental emissions”.
Can be trawling in diesel-electric mode
“During the most energy-intensive operations, such as shrimp fishing with quadruple trawl, both main engines will be used, mechanically connected to each propeller to be most efficient at high power. But the vessel should also be able to operate efficiently with lighter trawling that requires less engine load, and it has been enabled to do so in diesel-electric mode with only one of the main engines in operation. Operating time between the engines will be reduced, while the operative engine will be allowed to run more optimally. The propellers can then run at a very low speed, which gives very high efficiency during trawling, the vessel will be quieter and little power is needed to operate the ship. In this way, the advantages of both diesel-mechanical and diesel-electric power systems are utilised, while many of the disadvantages will be avoided.
Battery as part of a hybrid package
The Battery Energy Storage System (BESS) is a central part of the hybrid power system and has the following functions:
Engine support: The battery actively assists the main engines, especially when the entire trawler is operated on only one diesel engine in diesel-electric mode. By letting the battery take care of the short-term increases in power demand, such as when the vessel turns during trawling, substantial amounts of energy are saved.
Response in the power system: The battery system in the solution has large power reserves and quick responsiveness. Having battery assistance, it will be easier for the diesel engine to work dynamically and handle load increases.
Reliability: The battery system increases the redundancy and uptime on the power grid should a fault occur in the power system.
Storing return power: The trawler has electric winches with power regeneration, when the trawl is slowed down, power will be released to the grid. This return power can be stored in the battery to be available when needed later.
Reduced emissions at quay: The battery system has a large energy capacity (approx. 1,130 kWh) which can not only support the ship in case of extra power needs but also means that the vessel can stay quayside for many hours before a diesel engine must start or shore power connected. The ship is also equipped with a modern shore connection that can fully utilise the port facilities that are currently under development. This means that the entire ship can be supplied from shore, and also the large battery can be charged by shore power. This will help to eliminate the need of running the diesel engines while quayside.
Ship designers and integrators - not only developing a vessel, but an entire system
Frode Sollid continues: “The people at Ulstein Design & Solutions are naval architects and integrators, we do not just develop a vessel, but an entire system. When we design a ship, we structure our work around the knowledge of what the ship will do, the work operations and where the ship will be operating”.
“Knowing how much power is needed throughout the year to perform the various operations under different conditions, we have defined a hull that is adapted to the environment in which it will be used. With the good experiences of the X-BOW® in other ship types we have developed a hull that is tailor-made for this type of ship. An X-BOW provides a volume distribution that we benefit from when arranging the fore ship. Together with the choice to optimise the hull lines for a speed of 10-12 knots, this means that the vessel has larger capacities than one can typically expect from a fishing vessel of this length”.
Flexible and future-oriented
“The hybrid propulsion system of the Bluewild trawler is a very future-oriented solution that makes it possible to conduct different types of fishing in an efficient way and ensures future opportunities for new fisheries that may come. Many elements together make this trawler a masterpiece”, concludes Sollid.